<track id="bkkx1"><div id="bkkx1"></div></track>

<track id="bkkx1"><div id="bkkx1"></div></track>
<bdo id="bkkx1"><dfn id="bkkx1"><thead id="bkkx1"></thead></dfn></bdo>

    <track id="bkkx1"></track>

    新聞中心

    NEWS CENTER

    • 吸附式干燥機的加熱塔如何工作?
    • 本站編輯:杭州天源氣超濾設備工程有限公司發布日期:2022-05-16 17:15 瀏覽次數:

    吸附式干燥機也可以叫做微熱再生吸附式干燥機,其主要構造的名稱為:A塔、B塔、A進氣伐、B進氣閥、A再生伐、B再生伐、加熱器、消音器、二位五通電磁氣動閥、程控器、單相伐、節流孔板等部件組成。

    工作的程序為:A塔吸附時-A進氣伐(開)-B進氣閥(關)-A再生伐(關)-B再生伐(開),這樣壓縮空氣從A進氣閥進入A塔,由下至上在經過塔體內的時候內部氧化鋁或分子篩將水分吸附,干燥的空氣就是這樣出來的,2小時后切換至B塔吸附,所有的伐件與A塔吸附時的狀態相反,由于上周期A塔吸附的水分存留在塔內吸附劑里,需要在B塔吸附的時間內把A塔的水分排出A塔外故叫做A塔再生,利用B塔吸附干燥后的空氣,先經過節流孔板減壓,再到加熱桶內加熱到160度左右,這樣高溫低壓的干燥空氣進入A塔,由上至下的將塔內的濕氣水分排出塔外。

    一個周期2小時到后在切換到A塔吸附B塔再生,其實就是1種干燥模式2個干燥系統,這樣就不需要停機就可以源源不斷的供應干燥的壓縮空氣了。

    The adsorption dryer can also be called micro heat regeneration adsorption dryer. Its main structure is composed of tower a, Tower B, a inlet valve, B inlet valve, a regeneration valve, B regeneration valve, heater, silencer, two position five way electromagnetic pneumatic valve, program controller, single-phase valve, throttle orifice and other components.

    The working procedure is as follows: during adsorption of tower a - a inlet valve (on) - B inlet valve (off) - a regeneration valve (off) - B regeneration valve (on), so that the compressed air enters tower a from the inlet valve of tower A. when passing through the tower from bottom to top, the internal alumina or molecular sieve adsorbs the water. The dry air comes out in this way. After 2 hours, it is switched to Tower B for adsorption. All cutting parts are in the opposite state to that during adsorption of tower a, Since the water adsorbed by tower a in the previous cycle is stored in the adsorbent in the tower, it is necessary to discharge the water of tower a out of tower a within the adsorption time of Tower B, so it is called tower a regeneration. Tower B is used to adsorb the dried air, depressurize it through the orifice plate, and then heat it to about 160 degrees in the heating barrel. In this way, the dry air with high temperature and low pressure enters tower a, and the moisture in the tower is discharged out of the tower from top to bottom.

    After a cycle of 2 hours, switch to tower a for adsorption and Tower B for regeneration. In fact, it is one drying mode and two drying systems, so that dry compressed air can be supplied continuously without shutdown.